Download PDF
[v1]Mon, 18 Dec 2017 19:13:25 UTC (2,425 KB)
Full-text links:![Homemade laser diode driver/ download last version 1 Homemade laser diode driver/ download last version 1](http://letkol.mohammedshrine.org/preview/NGZXP/laser-diode-driver-simple-circuit-diagram.gif)
Abstract: We present an inexpensive, low-noise ($<260~mu$V$_{rms}$, 0.1~Hz - 100~kHz)design for a piezo driver suitable for frequency tuning of external-cavitydiode lasers. This simple driver improves upon many commercially availabledrivers by incorporating circuitry to produce a `feed-forward' signalappropriate for making simultaneous adjustments to the piezo voltage and lasercurrent, enabling dramatic improvements in mode-hop-free laser frequency tuningrange. We present the theory behind our driver's operation, characterize itsoutput noise, and demonstrate its use in absorption spectroscopy on therubidium D$_1$ line.
Submission history
Download PDF. Driver with feed-forward for broad tuning of external cavity diode lasers. This simple driver improves upon many commercially available. For making simultaneous adjustments to the piezo voltage and laser. (or arXiv:1712.06627v1 physics.ins-det for this version). New recent 1712.
From: S. Charles Doret [view email] [v1]Mon, 18 Dec 2017 19:13:25 UTC (2,425 KB)
Full-text links:
Download:
Current browse context:
< prev | next >
Change to browse by:
physics
physics.atom-ph
physics.atom-ph
References & Citations
![Homemade laser diode driver/ download last version 1 Homemade laser diode driver/ download last version 1](http://letkol.mohammedshrine.org/preview/NGZXP/laser-diode-driver-simple-circuit-diagram.gif)
- INSPIRE HEP
(refers to | cited by )
Which authors of this paper are endorsers? | Disable MathJax (What is MathJax?) Browse v0.2.7 released 2019-12-16
Small compact, constant current source for driving LEDs and lasers up to 4A with PWM capabilities and integrated support to drive 3 loads such as fans.
Board specification
Schematic
Electrical characteristics
V(in) range: 4V..18V, observe input caps ratings
Max. main load current: 3.3A observe inductor ratings
Max. aux load currents: 500mA depends on transistor selection
Dim. threshold voltage: 1.2V
Duty cycle range: 0%..100%
Soft start duration: 1.2ms
Dim. frequency range: 400Hz..4KHz
Mechanical
Board dimensions: 32mm x 32mm
Supply and main load dimming: 1 x 3 pin, 2.54mm connector
Main load connector: 1 x 2 pin, 2.54mm connector
Aux. load dimm. connector: 1 x 3 pin, 2.54mm connector
Aux. load connector: 3 x 2 pin, 2.54mm connector
PCB fabrication: Pattern class 6, drills clase C. Any cheap PCB manufacturer should be more than capable of making your boards. Do not shrink track widths.
Observe connector current ratings for your application.
Measured performance
Performance: Measure performance 83% @ 12V, 1A load. Tested with a 3W LED.
Operation and setup
Connect power supply to the supply and main load dimming connector observing the polarity(V+, DIM, V-) within the board's tolerance and ensure that your supply is capable of sourcingthe current required by your load.
Connect the load (LED or laser driver) observing the polarity of your device.
If you use auxiliary loads connect them to the auxiliary load connectors and observe their polarity.The board has built in freewheel diodes, you should be good to go with any type of load provided you don'texceed switching ratings.
Each auxiliary load channel is controlled with a control signal from the aux load connector. By defaultloads are inactive. A voltage level of 5V (depending on your FET selection) will activate each channel.
Soft start
The board is configured to do a soft start. Apply a 1.2ms (minimum) pulse to the dimm pin beforestarting the PWM operation.
Waveforms and captures
A couple of waveform capture showing the performance of the driver. Measurement setup:
- Supply voltage: 5V
- Load current: 1A
To start the driver it needs a 1.1ms pulse on the dimming pin.
976Hz PWM duty cycle captures.
Raising edge, measuring directly the LED voltage on switch on. 10us, raising edge with very littleovershoot and ringing. Very decent current control and regulation.
Ripple and noise is around 20mV, I think that about half of it comes from my measurement setup. 20MHzbandwidth limit.
Disclaimer
The board has only been tested to switch a 3W LED driven at 1A. It should be more than capable of reachingit's full specifications provided that you don't exceed the current ratings of the components you mount.
License
The board is released under the CERN OHL v1.2 but if you like it and use it you can buy me some beer.If you use it and/or do any derivative work from it, be nice and give attribution to the source.